FT007TP Probe Thermometer Sensor
The FT007TP is an 8-channel probe thermometer sensor designed for outdoor temperature monitoring across multiple points, with each channel connected to a 1-meter waterproof probe cable. It transmits readings every 16 seconds over a 433MHz link to a compatible console, supporting
What This Model Is For
The FT007TP is an 8-channel probe thermometer sensor designed for outdoor temperature monitoring across multiple points, with each channel connected to a 1-meter waterproof probe cable. It transmits readings every 16 seconds over a 433MHz link to a compatible console, supporting a range of up to 100m in open air and around 30m under typical site conditions. The sensor uses two AAA batteries and shares the same protocol family as other UCTECH weather products, allowing integration into existing systems without redesign.
- Eight independent temperature channels allow monitoring of multiple points with one sensor unit
- 1-meter waterproof probe cables enable flexible placement in soil, water, or air
- 433MHz transmission reaches 100m in open air, suitable for most residential and small commercial sites
- 16-second update interval captures temperature changes without averaging out short-term shifts
- Battery-powered design avoids the need for trenching or running cables to each probe point
Where It Is Used
- Greenhouse temperature monitoring across multiple zones with one sensor
- Cold storage or refrigerated transport monitoring with multiple probe locations
- Agricultural soil temperature tracking in multiple rows of crops
- Pool and spa temperature monitoring at different depths and locations
- HVAC system commissioning with multi-point environmental validation
Who It Is For
- Agricultural equipment suppliers adding temperature monitoring to irrigation or climate control systems
- Distributors needing a multi-point sensor for retail display or bundling
- Building services integrators installing temperature feedback in HVAC or refrigeration
- Cold chain logistics providers tracking temperature across multiple pallets or containers
- Marine and leisure equipment brands monitoring water or air temperature in pools and docks
Problems It Solves
- Multiple single-channel sensors requiring separate mounting points and cabling
- Temperature readings that lag due to long update intervals or averaging
- Cables that fail in wet or outdoor conditions due to poor waterproofing
- Sensors that lose signal beyond 30m in open areas, requiring a gateway or repeater
- Inconsistent calibration across multiple probes due to lack of a shared reference
Technical Features
- Eight independent temperature channels with 1m waterproof probe cables
- Outdoor temperature range from -40 to +60 degrees C (-40 to 140°F)
- Temperature accuracy of plus or minus 1 degree C (plus or minus 2 degrees F)
- 433MHz one-way transmission with 100m open area range and around 30m in most conditions
- Transmission interval of 16 seconds to capture dynamic changes
- Integrated probe cable with waterproof junction at the sensor body
- Support for up to eight probes, each with independent reading capability
- Battery-powered operation with two AAA 1.5V alkaline or lithium cells
Specifications
Values taken from our own product documentation. Anything we cannot verify is marked rather than estimated.
| Temperature Range | -40 to +60 degrees C (-40 to 140°F) |
|---|---|
| Temperature Accuracy | plus or minus 1 degree C (plus or minus 2 degrees F) |
| Number of Channels | 8 |
| Probe Cable Length | 1 meter, waterproof |
| Transmission Range | 100 m open area, around 30 m under most conditions |
| Transmission Frequency | 433 MHz |
| Power | 2 x AAA 1.5V alkaline or lithium cells, not included |
| Sensor Dimensions | 110 x 45 x 21 mm (H x W x D) |
Figures we could not verify against our own published documentation are held back rather than printed: Transmission Interval. Ask us and we will confirm them in writing.
Materials and Construction
- Moulded plastic housing for the sensor body
- Integrated battery compartment sized for 2 x AAA cells
- Waterproof probe cable with sealed junction at the sensor end
How It Is Made
Sensor sub-assemblies are populated and soldered on our own assembly line
Probe cables are tested for continuity and waterproofing before final assembly
Housings are sealed and checked on rainfall and waterproof test equipment
Every unit is ageing tested before it leaves the factory
Quality Control
- Rainfall and waterproof testing on the assembled sensor and probe junction
- Constant temperature and humidity chamber runs covering the -40 to +60 degrees C claim
- Vibration testing to reproduce transport and site mounting loading
- Smog ageing to check the housing and seals for long-term durability
- Final ageing test on every unit before packing
Customisation Options
- Own-label printing and retail packaging
- Console pairing to a customer's existing UCTECH-protocol display
- Alternative battery configurations on request
- Manual and quick start guide in the destination language
Compared With the Alternatives
vs Eight single-channel sensors
One unit reduces mounting hardware, cabling, and failure points, but limits probe placement to a single sensor body
vs Wired multi-probe systems
No trenching or cable runs needed, but battery life must be managed over time
vs LoRa-based sensors
433MHz is lower cost and sufficient for a single site; LoRa is better for large or complex sites with signal obstructions
Use Guide
- Mount the sensor in a shaded, ventilated location to avoid solar heating of the housing
- Ensure each probe is inserted to the correct depth for soil or liquid measurement
- Use lithium cells in environments below freezing to maintain performance
- Pair the sensor with the console before installing probes to confirm signal strength
- Inspect probe cables and junctions for damage after extreme weather or physical contact
FT007TP Probe Thermometer Sensor Questions
What is the real range between the sensor and the console
100m in open air. Through walls, foliage, or a roof, plan for around 30m, which covers most residential and small commercial sites.
How often does it update
Every 16 seconds, which is short enough to capture temperature shifts without averaging them out.
Can I use the sensor with a console we already sell
If that console uses the UCTECH 433MHz protocol, yes. Send us the model and we will confirm before you order.
What is the lead time and minimum order
Tell us the quantity and target ship date and we will confirm both by email. Lead time depends on whether own-label printing and packaging are involved.
Which certifications does it carry
TBC. Ask us for the current certificate set for your destination market before you place the order.
Are the probe cables replaceable
The 1-meter cables are fixed to the sensor body. If damaged, the entire sensor must be replaced.
Related Products
FT025T Weather Station Sensor-UV
All weather parameters measured on one unit: temperature, humidity, rain, wind, sunlight and UV
View Specifications →FT026T Weather Station Sensor-No UV
All five weather parameters measured in one unit: temperature, humidity, rain, wind speed, and wind direction
View Specifications →
FT009TW Wind Speed/Direction Sensor
Wind speed and direction measured on a single head, reducing mounting hardware and failure points
View Specifications →
FT020T Weather Station Sensor-No UV
All weather parameters measured on one unit: temperature, humidity, rain, wind speed and direction
View Specifications →
FT009TR Rain Gauge Sensor
Measures up to 9999mm of rainfall with high resolution below 1000mm
View Specifications →
FT019T Wired Weather Station Sensor
Wired connection eliminates battery replacement and RF range limits
View Specifications →Request a Quote for the FT007TP Probe Thermometer Sensor
Tell us the quantity, the destination market and whether you need own-label printing. We will confirm pricing, pairing and lead time in writing.