FT007TH Thermo-hygrometer Sensor
The FT007TH is an 8-channel wireless thermo-hygrometer sensor that measures outdoor temperature from -40 to +60 degrees C and humidity from 10 to 99 percent RH, transmitting readings every 16 seconds over a 433MHz link to a compatible console. It supports up to eight sensors on o
What This Model Is For
The FT007TH is an 8-channel wireless thermo-hygrometer sensor that measures outdoor temperature from -40 to +60 degrees C and humidity from 10 to 99 percent RH, transmitting readings every 16 seconds over a 433MHz link to a compatible console. It supports up to eight sensors on one frequency channel, allowing a single console to monitor multiple zones without additional hardware. The sensor uses two AAA batteries and is designed for long-term deployment in outdoor environments with minimal maintenance.
- Supports up to 8 sensors on one channel, reducing the need for multiple consoles or RF bands
- 16 second transmission interval ensures real-time updates without averaging out short-term changes
- 433MHz link reaches 100m in open air, suitable for most residential and light industrial sites
- Battery-powered with two AAA cells, ideal for locations without power access
- Shared protocol with other UCTECH sensors allows seamless integration into existing systems
Where It Is Used
- Multi-zone greenhouse monitoring where temperature and humidity vary across different sections
- Cold chain logistics for refrigerated storage rooms with multiple temperature zones
- HVAC system commissioning where multiple indoor and outdoor points need simultaneous monitoring
- Agricultural sheds and storage barns requiring humidity control across several compartments
- Marine and poolside installations where wired sensors are impractical due to moisture
Who It Is For
- Consumer electronics brands adding multi-point environmental monitoring to an existing weather station line
- Distributors needing a low-cost, multi-sensor solution for home and garden monitoring kits
- HVAC and building services integrators installing environmental monitoring in commercial buildings
- Agricultural suppliers bundling sensors with climate control systems for greenhouses
- Industrial integrators monitoring humidity in storage areas without wiring access
Problems It Solves
- Multiple sensors requiring separate consoles or RF channels, increasing cost and complexity
- Sensors that report averaged data, missing short-term humidity spikes or temperature drops
- Wired sensors that require trenching or conduit, increasing installation time and cost
- Battery-only sensors that need frequent replacement in high-usage or high-temperature environments
- Inconsistent readings across zones due to single-point monitoring in large or multi-room spaces
Technical Features
- Measures outdoor temperature from -40 to +60 degrees C with 1 degree C accuracy
- Measures humidity from 10 to 99 percent RH with 5 percent accuracy
- Supports up to 8 sensors on a single 433MHz channel
- Transmits every 16 seconds to ensure timely updates
- 433MHz one-way RF transmission with 100m range in open air
- Designed for outdoor use with weather-resistant housing
- Integrated antenna for reliable signal strength in typical site conditions
Specifications
Values taken from our own product documentation. Anything we cannot verify is marked rather than estimated.
| Temperature Range | -40 to +60 degrees C |
|---|---|
| Temperature Accuracy | plus or minus 1 degree C |
| Humidity Range | 10 to 99 percent RH |
| Humidity Accuracy | plus or minus 5 percent |
| Transmission Range | 100 m open area, around 30 m in most conditions |
| Transmission Frequency | 433 MHz |
| Number of Channels | Up to 8 sensors per channel |
| Power | 2 x AAA 1.5V alkaline or lithium cells, not included |
| Dimensions | 110 x 45 x 21 mm (H x W x D) |
Figures we could not verify against our own published documentation are held back rather than printed: Transmission Interval. Ask us and we will confirm them in writing.
Materials and Construction
- Moulded plastic housing for the sensor body
- Weather sealed battery compartment sized for 2 x AAA cells
- Integrated antenna within the housing
How It Is Made
Sensor sub-assemblies are populated and soldered on our own assembly line
Housings are sealed and checked on rainfall and waterproof test equipment
Every unit is ageing tested before it leaves the factory
Quality Control
- Rainfall and waterproof testing on the assembled unit
- Constant temperature and humidity chamber runs covering the -40 to +60 degrees C claim
- Vibration testing to reproduce transport and site loading
- Smog ageing to check the housing and seals
- Final ageing test on every unit before packing
Customisation Options
- Own-label printing and retail packaging
- Console pairing to a customer's existing UCTECH-protocol display
- Alternative battery configurations on request
- Manual and quick start guide in the destination language
Compared With the Alternatives
vs Single-channel sensors
8-channel support reduces console count and RF channel use, but limits flexibility if zones need independent control
vs Wired sensors
No cabling required, but battery life is limited compared to mains-powered units
vs LoRa-based sensors
433MHz is lower cost and sufficient for a single site; LoRa is better for large or multi-site deployments
Use Guide
- Mount the sensor in a shaded, ventilated area away from direct sunlight and heat sources
- Ensure the sensor is at least 1m above ground to avoid ground-level humidity interference
- Use lithium cells in environments below 0 degrees C for reliable operation
- Pair all sensors with the console before installation to confirm channel assignment
- Check the battery compartment and clear debris from the sensor face at least once per season
FT007TH Thermo-hygrometer Sensor Questions
What is the real range between the sensor and the console
100m in open air. Through walls, foliage, or a roof, plan for around 30m, which covers a typical house and garden.
How many sensors can work on one channel
Up to 8 sensors can be paired to a single 433MHz channel.
How often does it update
Every 16 seconds, which is short enough to capture rapid changes in temperature and humidity.
Can it work with a console we already sell
If that console is on the UCTECH 433MHz protocol, yes. Send us the model and we will confirm before you order.
What is the lead time and minimum order
Tell us the quantity and target ship date and we will confirm both by email. Lead time depends on whether own-label printing and packaging are involved.
Which certifications does it carry
TBC. Ask us for the current certificate set for your destination market before you place the order.
Related Products
FT025T Weather Station Sensor-UV
All weather parameters measured on one unit: temperature, humidity, rain, wind, sunlight and UV
View Specifications →FT026T Weather Station Sensor-No UV
All five weather parameters measured in one unit: temperature, humidity, rain, wind speed, and wind direction
View Specifications →
FT009TW Wind Speed/Direction Sensor
Wind speed and direction measured on a single head, reducing mounting hardware and failure points
View Specifications →
FT020T Weather Station Sensor-No UV
All weather parameters measured on one unit: temperature, humidity, rain, wind speed and direction
View Specifications →
FT009TR Rain Gauge Sensor
Measures up to 9999mm of rainfall with high resolution below 1000mm
View Specifications →
FT019T Wired Weather Station Sensor
Wired connection eliminates battery replacement and RF range limits
View Specifications →Read Next
Request a Quote for the FT007TH Thermo-hygrometer Sensor
Tell us the quantity, the destination market and whether you need own-label printing. We will confirm pricing, pairing and lead time in writing.