Japanese Multifunctional Sink
Built for the compact kitchens that still expect a full prep station
What This Product Is And Who It Is For
A Japanese-style multifunction sink: one bowl, a stepped ledge, a sliding board and a drainer basket, with the faucet raised on a pedestal at the back of the deck.
It suits markets where kitchens are narrow and the sink has to absorb the jobs a drainer and a prep surface would normally do.
The layout keeps the working length short without giving up the accessory set.
Why Buyers Specify It
Short run, full function
Everything sits over one bowl, so the sink fits a run of worktop where a double bowl would not.
Raised faucet clears the board
The pedestal lifts the spout above the sliding board, so the board can pass underneath without catching.
Basket instead of a second bowl
A lift-out drainer basket handles rinsing and draining, which is what most buyers actually used the second bowl for.
Reads as a designed product
The pedestal, the board and the basket make the sink look specified rather than sourced.
What It Fixes In A Buying Programme
No room for a drainer
The basket and ledge do the draining inside the bowl.
Standard faucets foul the board
The raised pedestal gives clearance the board needs to slide.
Compact ranges look cheap
A pedestal spout and a matched board lift the perceived value of a small sink.
Who It Is For
- Brands selling into markets where kitchens are small and worktop length is the binding constraint
- Online retailers who need a photogenic sink that ships as one box
- Distributors building a compact-kitchen sub-range
Technical Features
- Single bowl with a stepped ledge on the long sides
- Raised pedestal faucet mount at the rear of the deck
- Hardwood sliding board cut to the ledge width
- Lift-out perforated drainer basket
- Brushed deck and bowl interior
Where It Ends Up
Apartment kitchens in Asia and Europe
Short worktop runs where a 1.5 or double bowl will not fit.
Studio and micro-living fit-outs
One sink covers prep, wash and drain in a kitchenette.
Kitchen renovation ranges
Replaces an old pressed bowl without changing the cut-out length dramatically.
Retail display
The pedestal faucet and loaded ledge make a strong shelf presentation.
Specification Table
Every figure we can evidence for this workstation sink is listed below. Where a dimension on the japanese multifunctional sink is set by your own order, or has not been measured and documented yet, the row reads TBC instead of a plausible-looking number.
| Product type | Japanese-style multifunction sink |
|---|---|
| Bowl configuration | Single bowl with ledge |
| Material | 304 stainless steel (202 / 201 on request) |
| Faucet mount | Raised rear pedestal |
| Included accessories | Sliding board, drainer basket |
| Overall size | TBC — confirm on enquiry |
| Bowl depth | TBC — confirm on enquiry |
| Steel thickness | TBC — confirm on enquiry |
Materials
Bowl, deck and pedestal are stainless steel — 304 unless another grade is agreed.
The sliding board is hardwood and the basket is perforated stainless. Board species is confirmed per order.
Customisation Options
- Bowl size adjusted to your cabinet module
- Pedestal height set to your preferred faucet
- Board in an alternative species, or a stainless board instead
- Deck punched for a side sprayer or soap dispenser
How It Is Made
Cut and notch
Sheet is cut and the ledge notches are set out before forming so the board width is fixed early.
Draw the bowl
The bowl is formed and the ledge step is pressed into the side walls.
Build the pedestal
The faucet pedestal is welded to the deck and dressed flush.
Brush and assemble
Deck and bowl are brushed, then the board and basket are fitted and checked for travel.
Quality Control
- The board is slid the full length of the ledge on every unit to confirm it does not bind.
- Pedestal welds are checked for pinholes before brushing.
- Each sink is water-tested at the drain before packing.
Certifications
No certification mark is claimed for the japanese multifunctional sink anywhere on this site, because we state only what a document can back up. If your market needs WaterMark, cUPC, CE or a material certificate against this workstation sink, raise it before the order and we will reply in writing on what is available for the japanese multifunctional sink.
Compared With A Standard 1.5-Bowl Sink
Buyers in compact kitchens usually compare this against a 1.5-bowl sink.
| Aspect | Japanese Multifunctional Sink | A Standard 1.5-Bowl Sink |
|---|---|---|
| Worktop length required | Short | Longer |
| Draining | Basket and ledge | Small second bowl |
| Prep surface | Sliding board over the bowl | None |
Use Guide
Step 1
Check the pedestal height against your chosen faucet before the deck is drilled.
Step 2
Slide the board back to open the bowl for filling pans.
Step 3
Lift the basket out to drain and rinse, then sit it back on the ledge.
Step 4
Dry the deck after use to keep the brushed grain even.
Japanese Multifunctional Sink — Frequently Asked Questions
Is the pedestal welded or bolted?
Welded to the deck and dressed flush. That is why the pedestal height needs to be agreed before production.
Can we order it without the board?
Yes — the sink is quoted as a bare bowl or with any part of the accessory set.
What is the minimum cabinet width?
It depends on the bowl size you specify. Send the cabinet module and we will confirm the largest bowl that fits.
Products And Reading That Go With This One
One basin that replaces the sink, the drainer and half the worktop
View product
The drainer is part of the sink, not a tray sitting on the worktop
View product
One deep bowl, a drilled ledge, and a finish choice that changes the price point
View productWorkstation sinks sell on the accessory photograph. They get returned on accessory fit. Everything…
Read the guideThe three mounting types are not three styles of the same product. They demand different worktops,…
Read the guideOne factory behind a whole stainless range
See the applicationOne specification, several hundred kitchens, no surprises
See the applicationQuote Japanese Multifunctional Sink
Send the quantity, the steel grade, the finish and any dimensions you need changed. If you are replacing an existing supplier, a sample is faster than a drawing.