Double Bowl Customizable Stainless Steel Topmount Sink
The volume double bowl, with the ledge and accessories buyers actually ask for
What This Product Is And Who It Is For
A double bowl topmount kitchen sink with a rear tap ledge, produced in brushed 304 stainless and in a gold PVD finish.
It is the range workhorse for distributors and kitchen brands: one cut-out, two bowls, and accessories that can be added per SKU.
A drainer rack, colander and board can be supplied on the ledge version.
Why Buyers Specify It
One cut-out, simple installation
Topmounting means a straight aperture and no support cradle, which keeps fitting costs down on volume projects.
Tap ledge keeps holes out of the stone
Drilling the sink rather than the worktop protects the fabricator from a cracked slab.
Accessory versions from one body
Bare, with rack, or with the full colander and board set — the same fabrication behind all three.
Gold PVD without a second body
A colour SKU that shares dimensions and spares with the steel version.
What It Fixes In A Buying Programme
Drilling stone for taps is a risk
The tap ledge takes the holes instead.
Every accessory variant needs new tooling
Not here — accessories are added to a common body.
Colour finishes complicate spares
The gold version shares dimensions with the steel one.
Who It Is For
- Distributors who need one body to cover several price points
- Kitchen brands running a stainless volume range
- Contractors on refurbishment programmes
Technical Features
- Two bowls with a low divider
- Rear tap ledge, drilled to order
- Brushed stainless or gold PVD finish
- Optional drainer rack, colander and board
- Sound-deadening pads on the underside (specify at order)
Where It Ends Up
Volume residential projects
Same sink, many apartments, one simple cut-out.
Retail and e-commerce ranges
Accessory variants create price points without new tooling.
Rental refurbishment
Quick to replace without touching the worktop underside.
Small commercial kitchens
Two bowls and a rack for a tea point or a servery.
Double Bowl Customizable Stainless Steel To… In Detail
Factory photographs of the double bowl customizable stainless steel to…. Every finish and accessory combination visible on the double bowl customizable stainless steel to… can be ordered as shown.
Specification Table
Every figure we can evidence for this topmount sink is listed below. Where a dimension on the double bowl customizable stainless steel to… is set by your own order, or has not been measured and documented yet, the row reads TBC instead of a plausible-looking number.
| Product type | Topmount kitchen sink |
|---|---|
| Bowl configuration | Double bowl with tap ledge |
| Material | 304 stainless steel (202 / 201 on request) |
| Finish | Brushed stainless or gold PVD |
| Tap holes | Drilled to order |
| Overall size | TBC — confirm on enquiry |
| Bowl depth | TBC — confirm on enquiry |
| Steel thickness | TBC — confirm on enquiry |
| Accessories | Rack, colander, board — specify per SKU |
Materials
304 stainless steel as standard. 202 and 201 are produced where a price-led range needs them — the difference matters most in hard or chlorinated water.
Gold is a PVD coating over the finished body, not a plating.
Customisation Options
- Bowl split and overall size
- Number and spacing of tap holes
- Finish — brushed, gold PVD, black PVD
- Accessory pack per SKU
How It Is Made
Cut and form
Both bowls and the ledge are set out on one blank.
Weld and dress
Corners and the divider are welded and ground back.
Drill the ledge
Tap holes are punched to the order sheet, not to a standard.
Finish
Brushed, then PVD coated if a colour SKU.
Quality Control
- Tap hole positions are checked against the order sheet before finishing.
- Both bowls water-tested.
- PVD batches compared to the colour reference before packing.
Certifications
No certification mark is claimed for the double bowl customizable stainless steel to… anywhere on this site, because we state only what a document can back up. If your market needs WaterMark, cUPC, CE or a material certificate against this topmount sink, raise it before the order and we will reply in writing on what is available for the double bowl customizable stainless steel to….
Compared With An Undermount Double Bowl
The same kitchen can take either a topmount or an undermount double bowl.
| Aspect | Double Bowl Customizable Stainless Steel To… | An Undermount Double Bowl |
|---|---|---|
| Installation | Drop in, seal, done | Cradle and clips required |
| Tap holes | In the sink ledge | In the worktop |
| Worktop edge | Rim sits on the surface | Continuous stone into the bowl |
Use Guide
Step 1
Confirm tap hole count and spacing before production — the ledge is drilled, not field-modified.
Step 2
Bed the rim on a neutral-cure silicone.
Step 3
Lift and rinse the drainer rack weekly.
Step 4
On PVD finishes use a soft cloth and neutral detergent only.
Double Bowl Customizable Stainless Steel To… — Frequently Asked Questions
Can we order it undrilled?
Yes, for installations where the tap goes in the worktop or on the wall.
Does the gold version cost more to ship?
It is the same body and the same weight. The coating is the only difference in the price.
Are the accessories interchangeable between sizes?
Only within the same bowl dimension. Racks and colanders are cut to the bowl they ship with.
Products And Reading That Go With This One
One deep bowl, a drilled ledge, and a finish choice that changes the price point
View product
Two bowls, your split, one fabricated body
View product
Both bowls, one outlet, no rigid pipe to cut on site
View productThe three mounting types are not three styles of the same product. They demand different worktops,…
Read the guideAll three grades are austenitic stainless and all three make a usable sink. What differs is how…
Read the guideStock that moves, with the waste kit already in the box
See the applicationOne specification, several hundred kitchens, no surprises
See the applicationQuote Double Bowl Customizable Stainless Steel To…
Send the quantity, the steel grade, the finish and any dimensions you need changed. If you are replacing an existing supplier, a sample is faster than a drawing.