FT0076 Wireless Thermometer
The FT0076 is a wireless thermometer system with a console and two remote sensors that measure indoor and outdoor temperature across a 0 to 60 degrees C range indoors and -40 to 60 degrees C outdoors, transmitting readings every 60 seconds over a 433MHz link up to 100 meters in o
What This Model Is For
The FT0076 is a wireless thermometer system with a console and two remote sensors that measure indoor and outdoor temperature across a 0 to 60 degrees C range indoors and -40 to 60 degrees C outdoors, transmitting readings every 60 seconds over a 433MHz link up to 100 meters in open air. It supports up to eight sensors on one console and includes min/max recording and manual calibration for temperature. The system is designed for brands needing a ready-to-use temperature monitoring solution without developing their own RF or firmware stack.
- Measures indoor and outdoor temperature across a wide range, from -40 to +60 degrees C
- Transmits every 60 seconds, allowing trend tracking without constant data overload
- 100 meter open-air range on 433MHz enables placement across a typical home or garden
- Console supports up to eight sensors, allowing expansion without new hardware
- Manual calibration adjusts for site-specific temperature drift, improving long-term accuracy
Where It Is Used
- Home and office temperature monitoring for smart building integrators
- Greenhouse and nursery climate tracking where temperature extremes affect plant health
- Retail and warehouse environments needing ambient temperature logs for compliance
- Distributors adding temperature visibility to a weather station bundle
- Cold chain logistics where temperature trends matter more than real-time alerts
Who It Is For
- Consumer electronics brands launching an own-label thermometer without RF development
- Distributors replacing a sensor that failed after one winter due to cold or vibration
- Agricultural suppliers bundling temperature monitoring with irrigation or heating controls
- HVAC integrators needing a low-cost, expandable temperature monitoring layer
Problems It Solves
- Sensors that fail in sub-zero conditions due to untested cold tolerance
- RF links that drop out beyond 30 meters, requiring a gateway or cabling
- Temperature readings that drift over time without a calibration method
- Console systems that only support two sensors, limiting site coverage
- Brands forced to build their own firmware stack to add temperature monitoring
Technical Features
- Indoor temperature range: 0 to 60 degrees C
- Outdoor temperature range: -40 to 60 degrees C
- Temperature accuracy: plus or minus 1 degree C
- Transmission frequency: 433 MHz
- Transmission interval: 60 seconds
- Transmission range: 100 meters in open air
- Console supports up to 8 sensors
- Min/max temperature recording for both indoor and outdoor sensors
- Manual temperature calibration via console
- Temperature trend indication on LCD display
- Two remote sensors included, each with its own channel (CH1, CH2)
Specifications
Values taken from our own product documentation. Anything we cannot verify is marked rather than estimated.
| Indoor Temperature Range | 0 to 60 degrees C |
|---|---|
| Outdoor Temperature Range | -40 to 60 degrees C |
| Temperature Accuracy | plus or minus 1 degree C |
| Transmission Frequency | 433 MHz |
| Transmission Interval | 60 s |
| Transmission Range | 100 m open area |
| Number of Sensors Supported | Up to 8 |
| Console Power | 4 x AAA 1.5V LR6 Alkaline batteries |
| Sensor Power | 2 x AAA 1.5V LR6 Alkaline or lithium cells |
| Console Dimensions | 115 x 125 x 24 mm |
| Sensor Dimensions | 45 x 110 x 21 mm |
| LCD Display Size | 95 x 80 mm (5 inch) |
Materials and Construction
- Moulded plastic housing for the console and sensor
- Weather sealed battery compartment sized for 2 x AAA cells
- Integrated antenna in the sensor housing for 433MHz transmission
How It Is Made
Sensor and console sub-assemblies are populated and soldered on our own assembly line
Each sensor is tested for transmission stability and signal strength
Housings are sealed and checked on rainfall and waterproof test equipment
Every unit undergoes a final ageing test before packing
Quality Control
- Rainfall and waterproof testing on the assembled sensor and console
- Constant temperature and humidity chamber runs covering the -40 to +60 degrees C range
- Vibration testing to simulate transport and mounting stress
- Smog ageing to check housing and seal integrity
- Final ageing test on every unit before packing
Customisation Options
- Own-label printing and retail packaging
- Console pairing to a customer's existing UCTECH-protocol display
- Alternative battery configurations on request
- Manual and quick start guide in the destination language
Compared With the Alternatives
vs Wired temperature sensors
No cable run required, but limited by battery life and 100m range ceiling
vs LoRa-based sensors
433MHz is lower cost and sufficient for a single property; LoRa is needed for larger sites
vs Sensors without manual calibration
Manual calibration allows correction for drift, improving long-term accuracy
Use Guide
- Mount the sensor in a shaded outdoor location, away from direct sun and heat sources
- Place the console indoors, at least 1 meter from large metal objects or microwaves
- Use lithium cells in the sensor if operating below 0 degrees C
- Pair the sensors with the console before mounting them outside
- Check battery levels monthly and replace before the system stops reporting
FT0076 Wireless Thermometer Questions
What is the real range between the sensor and the console
100 meters in open air. Through walls, foliage or a roof, expect around 30 meters, which covers a typical house and garden.
How often does it update
Every 60 seconds, which balances data freshness with battery life.
Can I add more than two sensors
Yes. The console supports up to eight sensors. Order additional transmitters separately.
Does it work with a console we already sell
If that console uses the UCTECH 433MHz protocol, yes. Send us the model and we will confirm before you order.
What is the lead time and minimum order
Tell us the quantity and target ship date and we will confirm both by email. Lead time depends on whether own-label printing and packaging are involved.
Which certifications does it carry
TBC. Ask us for the current certificate set for your destination market before you place the order.
Related Products
FT-0170 Wireless Thermo-hygrometer with 3 Channels
Three independent outdoor sensor channels allow monitoring of different zones without additional receivers
View Specifications →
FT0418 Wireless Thermometer
Measures indoor, fridge, and freezer temperatures with a single sensor system
View Specifications →
FT0424 Wireless Thermometer
Measures indoor, fridge, and freezer temperatures with one console, reducing the need for multiple devices
View Specifications →
FT0423 Wireless Thermo-Hygrometer
Measures both indoor and outdoor temperature and humidity in one system
View Specifications →
FT0420 Wireless Thermometer
Measures indoor and outdoor temperature with a single sensor and console
View Specifications →
FT0413 Wireless Thermo-Hygrometer
Measures both indoor and outdoor temperature and humidity in one system
View Specifications →Request a Quote for the FT0076 Wireless Thermometer
Tell us the quantity, the destination market and whether you need own-label printing. We will confirm pricing, pairing and lead time in writing.