Cummins KTAA19-C700 Diesel Engine 700HP Construction Engine
Cummins KTAA19-C700 6-cylinder in-line diesel engine rated 522 kW (700 HP) at 2100 rpm with 19 L displacement for excavators, wheel loaders, cranes, drill rigs and other off-highway machines.
- Home
- Products
- Construction Engines
- Cummins KTAA19-C700 Diesel Engine 700HP Construction Engine
What This Engine Is Built For
The Cummins KTAA19-C700 is a 6-cylinder in-line construction diesel engine of 19 L with a 159 * 159 mm bore and stroke supplied by MEP Power as a complete assembly. It is rated at 522 kW (700 HP) at 2100 rpm and develops 2731 N.m @ 1300 rpm. The engine is turbocharged-intercooled and water cooled, with a Direct Injection PT Pump fuel system. It is built at the Chongqing Cummins Plant and carries Euro II. Typical duty is excavators, wheel loaders, cranes, drill rigs and other off-highway machines; dry weight with flywheel and alternator is 2073 Kg and the overall envelope is 2150mm*966mm*1704mm.
Key Benefits
- Delivers 522 kW (700 HP) at 2100 rpm from 19 L as a factory-rated assembly.
- Peak torque of 2731 N.m @ 1300 rpm holds the load without downshifting or derating.
- Turbocharged-Intercooled induction with water cooling keeps charge temperature under control in continuous duty.
- Supplied to Euro II, so the unit can be registered in markets that require it.
- Dry weight 2073 Kg and envelope 2150mm*966mm*1704mm are published so the installation can be checked before ordering.
- Rated for continuous running up to 2000 m Min altitude.
Application Scenarios
- 20-35 t excavator power unit replacement
- Wheel loader and grader repower
- Crawler crane and drill rig drive
- Concrete pump and batching plant drive
Who It Is For
- Excavator and loader rebuilders replacing a failed power unit
- Plant hire fleets that need machines back on rent quickly
- OEM machine builders sourcing a proven engine for a new chassis
- Quarry and earthmoving contractors running machines in dusty, high-load duty
Problems It Solves
- A machine down in the middle of a job stops the whole site, not just one asset.
- Rebuilt short blocks of unknown history fail again inside the warranty window.
- Dust, vibration and long hours at high load expose any weakness in the power unit.
- Identifying the right KTAA19-C700 variant from a serial number takes experience; MEP Power checks the configuration before quoting.
Specification As Published
Values below are the published data for this unit. Where a figure is not listed it was not stated by the source data sheet; ask and we will confirm before you order.
| Model | KTAA19-C700 |
| Type | 6 Cylinders in Line |
| Displacement | 19 L |
| Bore x Stroke | 159 * 159 |
| Engine Configuration Number | D193077CX02 |
| Net Weight (with flywheel and alternator) | 2073 Kg |
| Overall Dimension | 2150mm*966mm*1704mm |
| Manufacturing Plant | Chongqing Cummins Plant |
| Rated Power/Speed | 522 kW/700HP |
| Rated Speed | 2100 rpm |
| Max Torque/Speed | 2731 N.m @ 1300 rpm |
| Max Continuous Running Altitude | 2000 m Min |
| Low Idle Speed | 725 rpm |
| Fuel Consumption at Rated Power | 210g/Kw.h |
| Certification | Euro II |
| Aspiration | Turbocharged-Intercooled |
| Fuel System | Direct Injection PT Pump |
| Compression Ratio | 13.9:1 |
| Electrical System (starter motor/alternator) | 12V/24V |
| Lowest Starting Temp (without auxiliary system) | -12℃ |
| Engine Cooling Fluid Volume | Fluid Cooling |
| Cooling Method | Water Cooled |
Technical Features
- Cylinders: 6 Cylinders in Line
- Displacement: 19 L
- Bore and stroke: 159 * 159
- Aspiration: Turbocharged-Intercooled
- Fuel system: Direct Injection PT Pump
- Electrical system: 12V/24V
- Compression ratio: 13.9:1
- Coolant capacity: Fluid Cooling
Quality Control
- Every engine is inspected by the MEP Power inspection team before it leaves the warehouse
- Engine, configuration and serial numbers are recorded and photographed for the buyer
- Genuine and OEM units are quoted separately so the buyer knows exactly what is supplied
- Warranty on genuine and OEM new engines and generator sets is one year or 1000 hours, whichever comes first; parts and repair labour are covered for quality faults inside that period.
Use and Installation Guide
- Quote the model KTAA19-C700 and the engine configuration number D193077CX02 when ordering so the correct variant is supplied.
- Confirm flywheel housing, SAE size and pump drive against the machine
- Transfer the machine's own wiring harness only after checking the connector layout
- Run the first 50 hours at moderate load before full-duty work
- Keep the warranty terms in mind: one year or 1000 hours, whichever comes first.
Customisation Options
- OEM and ODM builds, including your logo and company name on the unit
- Cummins engine customisation and modification to your requirement
- Mining and special explosion-proof builds
- Genuine or OEM parts specified on the quotation
How It Compares
| Compared with | What to consider |
|---|---|
| A rebuilt or used engine of the same rating | A rebuilt unit may show the same 522 kW (700 HP) on paper, but its running history is unknown and the warranty rarely covers the whole engine. |
| A larger engine in the same KTAA19 range | Moving up a frame size adds weight, envelope and fuel burn; specify the next size up only if the duty cycle really needs the headroom. |
| A non-Cummins engine of similar output | Parts and service for Cummins families are available in most markets, which matters more over ten years than the purchase price on day one. |
KTAA19-C700 Questions
Is this KTAA19-C700 a genuine Cummins engine
What power does the KTAA19-C700 produce
What warranty comes with the engine
How do I confirm this is the right variant for my machine
How is the engine shipped and what payment terms apply
Other Models Buyers Compare With This One
Cummins QSKTAA19-C755 Diesel Engine 755HP Construction Engine
Cummins C755 6-cylinder in-line diesel engine rated 563 kW (755 HP) at 1800 rpm with 19 L displacement for excavators, wheel loaders, cranes, drill rigs and other off-highway machines.
View specification
Cummins QSKTAA19-C700 Diesel Engine 700HP Construction Engine
6-cylinder in-line diesel engine for excavators, wheel loaders, cranes, drill rigs and other off-highway machines, supplied as the Cummins C700 at 522 kW (700 HP) at 2000 rpm from 19 L.
View specification
Cummins QSM11-400 Diesel Engine 400HP Construction Engine
6-cylinder in-line diesel engine for excavators, wheel loaders, cranes, drill rigs and other off-highway machines, supplied as the Cummins QSM11-400 at 298 kW (400 HP) at 2100/1800 rpm Max Torque/Speed (2100): 1898 N.m @ 1400 rpm from 10.8 L.
View specificationQuote The KTAA19-C700
Send your serial number or nameplate photograph and we will confirm the configuration, then price genuine and OEM options side by side.