Generator Engines · 6LTAA9.5
Cummins 6LTAA9.5-G1 290KW 389HP Generator Engine
6-cylinder in-line diesel engine for prime and standby generator sets, supplied as the Cummins 6LTAA8.9-G3 at 290 kW (389 HP) at 1500 rpm from 8.9L.
- Home
- Products
- Generator Engines
- Cummins 6LTAA9.5-G1 290KW 389HP Generator Engine
Overview
What This Engine Is Built For
MEP Power supplies the Cummins 6LTAA8.9-G3 as a complete 6-cylinder in-line generator drive diesel engine of 8.9L running a 114 * 145 mm bore and stroke. It is rated at 290 kW (389 HP) at 1500 rpm. The engine is turbocharged/charge air cooled and water cooled, with a BYC P7100 Pump/GAC Governor fuel system. It is built at the Dongfeng Cummins Plant 6LTAA8.9-G3. Typical duty is prime and standby generator sets; dry weight with flywheel and alternator is 650 Kg and the overall envelope is 1149mm*799mm*1022mm.
Model6LTAA8.9-G3 (230kw)
Rated power230 kW (308HP)
Displacement8.9L
AspirationTurbocharged/Charge Air Cooled
Net weight650 Kg
Key Benefits
- Delivers 290 kW (389 HP) at 1500 rpm from 8.9L as a factory-rated assembly.
- Turbocharged/Charge Air Cooled induction with water cooling keeps charge temperature under control in continuous duty.
- Dry weight 650 Kg and envelope 1149mm*799mm*1022mm are published so the installation can be checked before ordering.
- Starts without auxiliary aids down to -12℃.
- Supplied as a complete engine assembly, so the unit goes straight onto the mounts
- Backed by a written warranty of one year or 1000 hours, whichever comes first
Application Scenarios
- Prime mover for a new generator set build
- Standby set engine replacement
- Rental power fleet rebuild
- Containerised power module
Who It Is For
- Genset packagers matching an engine to an alternator
- Rental power companies rebuilding sets between contracts
- Industrial sites replacing the prime mover in an existing canopy
- Telecom and data infrastructure contractors specifying standby power
Problems It Solves
- An engine that does not hold speed under block load makes the whole set unusable.
- Packagers lose weeks when the engine does not match the alternator and the base frame.
- Standby sets sit idle for months and must still start and take load on demand.
- Identifying the right 6LTAA8.9-G3 variant from a serial number takes experience; MEP Power checks the configuration before quoting.
Technical data
Specification As Published
Values below are the published data for this unit. Where a figure is not listed it was not stated by the source data sheet; ask and we will confirm before you order.
| Model | 6LTAA8.9-G3 (230kw) |
| Type | 6 Cylinders in Line, 4 Stroke Diesel |
| Displacement | 8.9L |
| Bore x Stroke | 114 * 145 |
| Net Weight | 650 Kg |
| Overall Dimension | 1149mm*799mm*1022mm |
| Manufacturing Plant | Dongfeng Cummins Plant 6LTAA8.9-G3 |
| Rated Power/Speed at 1500 rpm | 230 kW/308HP @ 1500 rpm Standby Power (1500 rpm): 250 kW/355HP @ 1500 rpm |
| Idle Speed | 850-950 rpm Fuel Consumption @ Running: ≤ 220g/Kw.h 6LTAA8.9-G3 |
| Aspiration | Turbocharged/Charge Air Cooled |
| Fuel System | BYC P7100 Pump/GAC Governor |
| Governor Type | Electronic, Regulation ≤5% |
| Compression Ratio | 16.6:1 |
| Electrical System (starter motor/alternator) | 12V/24V |
| Lowest Starting Temp (without auxiliary system) | -12℃ |
| Engine Cooling Fluid Volume | 11.1 L |
| Cooling Method | Water Cooled |
| Rated Power | 230 kW (308HP) |
| Rated Speed | 1500 rpm |
| Standby Power | 250 kW (335HP) |
| Cylinders | 6 Cylinders in-line |
| Prime Power | 290 kW/389HP |
Technical Features
- Cylinders: 6 Cylinders in Line, 4 Stroke Diesel
- Displacement: 8.9L
- Bore and stroke: 114 * 145
- Aspiration: Turbocharged/Charge Air Cooled
- Fuel system: BYC P7100 Pump/GAC Governor
- Governor: Electronic, Regulation ≤5%
- Electrical system: 12V/24V
- Compression ratio: 16.6:1
Quality Control
- Every engine is inspected by the MEP Power inspection team before it leaves the warehouse
- Engine, configuration and serial numbers are recorded and photographed for the buyer
- Genuine and OEM units are quoted separately so the buyer knows exactly what is supplied
- Warranty on genuine and OEM new engines and generator sets is one year or 1000 hours, whichever comes first; parts and repair labour are covered for quality faults inside that period.
Use and Installation Guide
- Quote the model 6LTAA8.9-G3 when ordering so the correct variant is supplied.
- Match the flywheel and SAE housing to the alternator before assembly
- Set the governor to the frequency required, 50 Hz or 60 Hz
- Run a load bank test before the set goes into service
- Keep the warranty terms in mind: one year or 1000 hours, whichever comes first.
Customisation Options
- OEM and ODM builds, including your logo and company name on the unit
- Cummins engine customisation and modification to your requirement
- Mining and special explosion-proof builds
- Genuine or OEM parts specified on the quotation
How It Compares
| Compared with | What to consider |
|---|---|
| A rebuilt or used engine of the same rating | A rebuilt unit may show the same 290 kW (389 HP) on paper, but its running history is unknown and the warranty rarely covers the whole engine. |
| A larger engine in the same 6LTAA9.5 range | Moving up a frame size adds weight, envelope and fuel burn; specify the next size up only if the duty cycle really needs the headroom. |
| A non-Cummins engine of similar output | Parts and service for Cummins families are available in most markets, which matters more over ten years than the purchase price on day one. |
Questions
6LTAA8.9-G3 Questions
Is this 6LTAA8.9-G3 a genuine Cummins engine
MEP Power supplies 100% genuine Cummins engines, generator sets and engine parts, plus OEM units and customised builds. Tell us which you need and the quotation will state clearly whether the unit offered is genuine, OEM or a customised build.
What power does the 6LTAA8.9-G3 produce
The rating supplied is 290 kW (389 HP) at 1500 rpm.
What warranty comes with the engine
New genuine and OEM engines and generator sets carry one year or 1000 hours, whichever comes first. Inside that period MEP Power supplies replacement parts free of charge and covers the cost of the engine repair for quality faults.
How do I confirm this is the right variant for my machine
Send the engine serial number or the nameplate photograph of the unit being replaced. MEP Power checks it against the 6LTAA8.9-G3 configuration before quoting.
How is the engine shipped and what payment terms apply
Shipment is by sea, air or express depending on size and urgency, arranged by MEP Power or by your own forwarder. Payment terms are Alipay, WeChat, T/T or L/C.
Related
Other Models Buyers Compare With This One
6LTAA9.5
Cummins 6LTAA9.5-G3 250KW 335HP Generator Engine
Cummins 6LTAA9.5-G3 6-cylinder in-line diesel engine rated 250 kW (335 HP) at 1500 rpm with 9.5L displacement for prime and standby generator sets.
View specification
QSK50
Cummins QSK50 Generator Diesel Engine 1580kW Generator Engine Assembly
16-cylinder diesel engine for prime and standby generator sets, supplied as the Cummins QSK50-G7 at 1421 kW from 50.3 L.
View specification
QSK50
Cummins QSK50 Generator Diesel Engine 1750kW Generator Engine Assembly
Cummins QSK50-G6 16-cylinder diesel engine rated 1574 kW with 50.3 L displacement for prime and standby generator sets.
View specificationWhere It Is Used
Quote The 6LTAA8.9-G3
Send your serial number or nameplate photograph and we will confirm the configuration, then price genuine and OEM options side by side.